[squid-users] wccp problem with squid

Hi

I have a problem with squid running wccp. For transparent proxy it works
fine if I set the gateway of my workstations
point to the squid machine. However the router does not seem to redirect
wccp packets to the squid.
In my opinion, the problem seems to be related with the ip_gre.c patched
file because the
gre counters shown by netstat -i -v are 0, but I am not sure and would
be very grateful if somebody could help me


netstat -v -i
Kernel Interface table
Iface MTU Met RX-OK RX-ERR RX-DRP RX-OVR TX-OK TX-ERR TX-DRP
TX-OVR Flg
eth0 1500 0 4922 0 0 0 647 0 0
0 BMRU
eth1 1500 0 1001 1 0 0 4863 3 0
0 BMRU
gre0 1476 0 0 0 0 0 0 0 0
0 ORU
lo 16436 0 10 0 0 0 10 0 0
0 LRU

[root@proxy squid]# ifconfig
eth0 Link encap:Ethernet HWaddr 00:E0:18:0A:1B:CF
          inet addr:195.126.56.2 Bcast:195.126.56.7
Mask:255.255.255.248
          UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
          RX packets:3971 errors:0 dropped:0 overruns:0 frame:0
          TX packets:532 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100
          RX bytes:278040 (271.5 Kb) TX bytes:45110 (44.0 Kb)
          Interrupt:10 Base address:0xa000

eth1 Link encap:Ethernet HWaddr 00:40:C7:97:32:E2
          inet addr:62.240.54.13 Bcast:62.240.54.15
Mask:255.255.255.248
          UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
          RX packets:945 errors:1 dropped:0 overruns:0 frame:0
          TX packets:4009 errors:3 dropped:0 overruns:0 carrier:3
          collisions:0 txqueuelen:100
          RX bytes:69250 (67.6 Kb) TX bytes:1244633 (1.1 Mb)
          Interrupt:9 Base address:0x8000

gre0 Link encap:UNSPEC HWaddr
00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
          inet addr:10.0.0.1 Mask:255.255.255.255
          UP RUNNING NOARP MTU:1476 Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

lo Link encap:Local Loopback
          inet addr:127.0.0.1 Mask:255.0.0.0
          UP LOOPBACK RUNNING MTU:16436 Metric:1
          RX packets:10 errors:0 dropped:0 overruns:0 frame:0
          TX packets:10 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:700 (700.0 b) TX bytes:700 (700.0 b)

I am starting the tunnel with the following command

/sbin/modprobe ip_gre
/sbin/ifconfig gre0 10.0.0.1 netmask 255.255.255.255 up


here is my squid.conf

httpd_accel_with_proxy on
httpd_accel_uses_host_header on
httpd_accel_host virtual 80
wccp_router 62.240.54.5
wccp_version 3
wccp_incoming_address 195.126.56.2
wccp_outgoing_address 195.126.56.2

 

Here is a show ip wccp on the cisco 3660 router

gate1#show ip wccp
Global WCCP information:
    Router information:
        Router Identifier: 62.240.54.5
        Protocol Version: 1.0

    Service Identifier: web-cache
        Number of Cache Engines: 1
        Number of routers: 1
        Total Packets Redirected: 0
        Redirect access-list: -none-
        Total Packets Denied Redirect: 0
        Total Packets Unassigned: 5934
        Group access-list: -none-
        Total Messages Denied to Group: 0
        Total Authentication failures: 0

Attached is the patched file ip_gre.c that I am using and the kernel
used is 2.4.18-5 on redhat 7.3 box and squid was installed with rpm from
redhat. Machine is live updated to the most recent versions

Regards

Chris

 
Received on Tue Jul 23 2002 - 11:16:30 MDT