Re: [squid-users] WCCP

> From: Amos Jeffries <squid3_at_treenet.co.nz>
> Date: Mon, 19 Oct 2009 17:05:15 +1300
> Cc: "squid-users_at_squid-cache.org" <squid-users_at_squid-cache.org>
> Subject: Re: [squid-users] WCCP
>
> Ross Kovelman wrote:
>>> From: Amos Jeffries <squid3_at_treenet.co.nz>
>>> Date: Mon, 19 Oct 2009 14:32:17 +1300
>>> Cc: "squid-users_at_squid-cache.org" <squid-users_at_squid-cache.org>
>>> Subject: Re: [squid-users] WCCP
>>>
>>> Ross Kovelman wrote:
>>>> I am going to be using WCCP. I did another reconfigure with the --enable
>>>> WCCP option. How can I check that it is on and running? The next step I
>>>> need to do is upgrade to version 2 since the Cisco only communicates on
>>>> version 2. I tried to do the patch < upgrade patch but then I get a
>>>> response with path to upgrade and I am not sure where the file is I need
>>>> patch.
>>> There is zero need to patch for support WCCPv2. It's been built into
>>> Squid for many years now.
>>>
>>> Run "./configure --help".
>>> * If it lists "--disable-wccpv2" there is no need to do anything.
>>> * If it lists "--enable-wccpv2" , add that to your build options.
>>> * If it does not mention "wccpv2" at all upgrade your Squid version.
>>>
>>> Then setup squid.conf with the relevant wccp2_* options.
>>>
>>> http://www.squid-cache.org/Doc/config/ or the wiki example configs have
>>> details on those.
>>>
>>> Amos
>>> --
>>> Please be using
>>> Current Stable Squid 2.7.STABLE7 or 3.0.STABLE19
>>> Current Beta Squid 3.1.0.14
>>
>>
>> Amos,
>>
>> Thanks again.
>> Running the ./configure --help only says this:
>> --disable-wccp Disable Web Cache Coordination V1 Protocol
>> --disable-wccpv2 Disable Web Cache Coordination V2 Protocol
>>
>> When I did the install I ran the ./configure --enable wccp option. I didn't
>> say --enable-wccpv2, does this matter? I also have this in the config:
>> wccp2_router 192.168.16.1
>> wccp2_forwarding_method 1
>> wccp2_return_method 1
>>
>> I am running Squid Web Proxy 2.7.STABLE5.
>
> Okay. Thats fine.
>
> The ./configure results mean that both WCCP versions are built into
> Squid by default unless you explicitly say --disable. Nothing extra
> needed to build them.
>
> The config options you have there are already WCCPv2-only options for
> Cisco. Nothing new needed there either.
>
> If thats not working its a config error somewhere.
>
> Amos
> --
> Please be using
> Current Stable Squid 2.7.STABLE7 or 3.0.STABLE19
> Current Beta Squid 3.1.0.14

Amos,

I am getting this in my cache log:

Accepting proxy HTTP connections at 0.0.0.0, port 3128, FD 20.
commBind: Cannot bind socket FD 21 to *:3128: (48) Address already in use
Accepting proxy HTTP connections at 0.0.0.0, port 80, FD 21.
commBind: Cannot bind socket FD 22 to *:80: (48) Address already in use
Accepting ICP messages at 0.0.0.0, port 3130, FD 22.
WCCP Disabled.
Accepting WCCPv2 messages on port 2048, FD 23.
Initialising all WCCPv2 lists

As from my other posting I need WCCP enabled but it is showing disabled.
Any reason why? How can I resolve this. Below is my lines in config

wccp2_router 192.168.16.1
wccp2_forwarding_method 1
wccp2_return_method 1